DVB-Cube <<< Das deutsche PC und DVB-Forum >>>
Diverse DVB Software für verschiedene Karten => # Linux DVB (vdr, kaffeine, ect.) => # VDR => Thema gestartet von: Dippes am 30 Oktober, 2009, 12:38
-
hallo,
ich versuche schon eine Woche meine neue x 10 Fb von pollin zum laufen zum bringen Fb Pollin (http://www.vdr-wiki.de/wiki/index.php/Fernbedienung_-_USB_X10)
ich habe lirc die lirc module installiert.das ati_remote Modul geblacklistet.die ausgabe von "lsmod | grep lirc" zeigt an das alle module geladen sind .
wenn ich irw eingebe kommt connection refused
ich mache da jetzt schon ne ewigkeit rum und komm da nicht mehr weiter.hat jemand ahnung wie man lirc einstellt?
-
ich habe lirc die lirc module installiert.das ati_remote Modul geblacklistet.die ausgabe von "lsmod | grep lirc" zeigt an das alle module geladen sind .
wenn ich irw eingebe kommt connection refused
du musst den lirc daemon aber schon vorher starten. Was sagt denn dmesg / syslog ?
-
danke erstmal für euer interesse ;)
das syslog:
[ 2.357494] brd: module loaded
[ 2.357799] Fixed MDIO Bus: probed
[ 2.358242] PNP: No PS/2 controller found. Probing ports directly.
[ 2.608508] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.609171] mice: PS/2 mouse device common for all mice
[ 2.609403] rtc_cmos 00:03: RTC can wake from S4
[ 2.609723] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.609829] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 2.609996] cpuidle: using governor ladder
[ 2.610053] cpuidle: using governor menu
[ 2.610121] No iBFT detected.
[ 2.611341] TCP cubic registered
[ 2.611397] NET: Registered protocol family 17
[ 2.611683] IO APIC resources could be not be allocated.
[ 2.611746] Using IPI No-Shortcut mode
[ 2.612325] registered taskstats version 1
[ 2.612741] rtc_cmos 00:03: setting system clock to 2009-10-30 18:04:21 UTC ( 1256925861)
[ 2.614100] Freeing unused kernel memory: 324k freed
[ 2.946112] processor ACPI_CPU:00: registered as cooling_device0
[ 2.953776] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.954258] ACPI: Thermal Zone [THRM] (30 C)
[ 3.808329] Uniform Multi-Platform E-IDE driver
[ 4.050343] amd74xx 0000:00:07.1: UDMA66 controller
[ 4.050421] amd74xx 0000:00:07.1: IDE controller (0x1022:0x7409 rev 0x07)
[ 4.050541] amd74xx 0000:00:07.1: not 100% native mode: will probe irqs later
[ 4.050611] ide0: BM-DMA at 0xf000-0xf007
[ 4.050686] ide1: BM-DMA at 0xf008-0xf00f
[ 4.050751] Probing IDE interface ide0...
[ 4.085590] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 4.133770] usbcore: registered new interface driver usbfs
[ 4.133945] usbcore: registered new interface driver hub
[ 4.140153] usbcore: registered new device driver usb
[ 4.147535] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.153702] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.159900] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.388144] hda: Maxtor 6Y120P0, ATA DISK drive
[ 4.401248] FDC 0 is a post-1991 82077
[ 4.668436] hdb: SAMSUNG SP1614N, ATA DISK drive
[ 4.724263] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 4.724412] hda: UDMA/66 mode selected
[ 4.724603] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 4.724666] hdb: UDMA/66 mode selected
[ 4.724778] Probing IDE interface ide1...
[ 5.460145] hdc: PLEXTOR DVDR PX-716A, ATAPI CD/DVD-ROM drive
[ 5.796188] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 5.796287] hdc: UDMA/66 mode selected
[ 5.796445] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.796629] ide1 at 0x170-0x177,0x376 on irq 15
[ 5.841772] SCSI subsystem initialized
[ 5.842494] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 5.842560] PCI: setting IRQ 11 as level-triggered
[ 5.842573] via-rhine 0000:00:09.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 5.847464] eth0: VIA Rhine II at 0x1d400, 00:05:5d:a2:51:ba, IRQ 11.
[ 5.848262] eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 45e1.
[ 5.848909] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
[ 5.848976] PCI: setting IRQ 12 as level-triggered
[ 5.848988] ehci_hcd 0000:00:08.2: PCI INT C -> Link[LNKC] -> GSI 12 (level, low) -> IRQ 12
[ 5.849290] ehci_hcd 0000:00:08.2: EHCI Host Controller
[ 5.849529] ehci_hcd 0000:00:08.2: new USB bus registered, assigned bus numbe r 1
[ 5.849703] ehci_hcd 0000:00:08.2: irq 12, io mem 0xeffffc00
[ 5.860113] ehci_hcd 0000:00:08.2: USB 2.0 started, EHCI 0.95
[ 5.860494] usb usb1: configuration #1 chosen from 1 choice
[ 5.860629] hub 1-0:1.0: USB hub found
[ 5.860713] hub 1-0:1.0: 4 ports detected
[ 5.861065] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.861130] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 5.861200] usb usb1: Product: EHCI Host Controller
[ 5.861255] usb usb1: Manufacturer: Linux 2.6.28-etobi.3-686 ehci_hcd
[ 5.861315] usb usb1: SerialNumber: 0000:00:08.2
[ 5.862909] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 5.862984] PCI: setting IRQ 10 as level-triggered
[ 5.862997] uhci_hcd 0000:00:08.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 5.863089] uhci_hcd 0000:00:08.0: UHCI Host Controller
[ 5.863289] uhci_hcd 0000:00:08.0: new USB bus registered, assigned bus numbe r 2
[ 5.863407] uhci_hcd 0000:00:08.0: irq 10, io base 0x0000cc00
[ 5.863761] usb usb2: configuration #1 chosen from 1 choice
[ 5.863892] hub 2-0:1.0: USB hub found
[ 5.863974] hub 2-0:1.0: 2 ports detected
[ 5.864488] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.864556] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 5.864626] usb usb2: Product: UHCI Host Controller
[ 5.864682] usb usb2: Manufacturer: Linux 2.6.28-etobi.3-686 uhci_hcd
[ 5.864741] usb usb2: SerialNumber: 0000:00:08.0
[ 5.865360] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
[ 5.865424] PCI: setting IRQ 9 as level-triggered
[ 5.865437] ohci_hcd 0000:00:07.4: PCI INT D -> Link[LNKD] -> GSI 9 (level, l ow) -> IRQ 9
[ 5.865596] ohci_hcd 0000:00:07.4: OHCI Host Controller
[ 5.865766] ohci_hcd 0000:00:07.4: new USB bus registered, assigned bus numbe r 3
[ 5.865896] ohci_hcd 0000:00:07.4: irq 9, io mem 0xeffcf000
[ 5.920476] usb usb3: configuration #1 chosen from 1 choice
[ 5.920627] hub 3-0:1.0: USB hub found
[ 5.920712] hub 3-0:1.0: 4 ports detected
[ 5.921044] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.921109] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 5.921178] usb usb3: Product: OHCI Host Controller
[ 5.921233] usb usb3: Manufacturer: Linux 2.6.28-etobi.3-686 ohci_hcd
[ 5.921292] usb usb3: SerialNumber: 0000:00:07.4
[ 5.922398] uhci_hcd 0000:00:08.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 5.922504] uhci_hcd 0000:00:08.1: UHCI Host Controller
[ 5.922682] uhci_hcd 0000:00:08.1: new USB bus registered, assigned bus numbe r 4
[ 5.922799] uhci_hcd 0000:00:08.1: irq 11, io base 0x0000d000
[ 5.923168] usb usb4: configuration #1 chosen from 1 choice
[ 5.923309] hub 4-0:1.0: USB hub found
[ 5.923393] hub 4-0:1.0: 2 ports detected
[ 5.923700] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.923764] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 5.923834] usb usb4: Product: UHCI Host Controller
[ 5.923890] usb usb4: Manufacturer: Linux 2.6.28-etobi.3-686 uhci_hcd
[ 5.923950] usb usb4: SerialNumber: 0000:00:08.1
[ 5.956181] libata version 3.00 loaded.
[ 6.059511] ide-gd driver 1.18
[ 6.059647] hda: max request size: 128KiB
[ 6.112079] hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/ 63
[ 6.112578] hda: cache flushes supported
[ 6.112815] hda: hda1 hda2 < hda5 hda6 >
[ 6.139168] hdb: max request size: 512KiB
[ 6.139724] hdb: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255 /63
[ 6.140301] hdb: cache flushes supported
[ 6.140526] hdb: unknown partition table
[ 6.164196] ide-cd driver 5.00
[ 6.184576] ide-cd: hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache
[ 6.184864] Uniform CD-ROM driver Revision: 3.20
[ 6.296167] usb 3-2: new low speed USB device using ohci_hcd and address 2
[ 6.528443] usb 3-2: configuration #1 chosen from 1 choice
[ 6.531703] usb 3-2: New USB device found, idVendor=0bc7, idProduct=0006
[ 6.531783] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.531846] usb 3-2: Product: RF receiver
[ 6.531900] usb 3-2: Manufacturer: X10 WTI
[ 6.721261] PM: Starting manual resume from disk
[ 6.812352] kjournald starting. Commit interval 5 seconds
[ 6.812457] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.396528] udevd version 125 started
[ 10.387024] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 10.486113] Linux agpgart interface v0.103
[ 10.541943] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 7007 ss_vid 0 s s_did 0
[ 10.542035] shpchp 0000:00:01.0: Cannot reserve MMIO region
[ 10.542145] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 10.709279] agpgart-amdk7 0000:00:00.0: AMD Irongate chipset
[ 10.718135] agpgart-amdk7 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[ 10.994819] lirc_dev: IR Remote Control driver registered, major 61
[ 11.064249]
[ 11.064253] lirc_atiusb: USB remote driver for LIRC $Revision: 1.69 $
[ 11.064371] lirc_atiusb: Paul Miller <pmiller9@users.sourceforge.net>
[ 11.100232] lirc_dev: lirc_register_plugin: sample_rate: 0
[ 11.168089] lirc_atiusb[2]: X10 WTI RF receiver on usb3:2
[ 11.184152] usbcore: registered new interface driver lirc_atiusb
[ 11.530145] ACPI: I/O resource amd756_smbus [0x50e0-0x50ef] conflicts with AC PI region SBS_ [0x50e0-0x50e8]
[ 11.530237] ACPI: Device needs an ACPI driver
[ 11.834960] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/inpu t/input0
[ 11.852060] ACPI: Power Button (FF) [PWRF]
[ 11.852441] input: Sleep Button (FF) as /devices/LNXSYSTM:00/LNXSLPBN:00/inpu t/input1
[ 11.868061] ACPI: Sleep Button (FF) [SLPF]
[ 11.868413] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0 C:00/input/input2
[ 11.880059] ACPI: Power Button (CM) [PWRB]
[ 13.505700] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 13.650638] Linux video capture interface: v2.00
[ 13.778931] gameport: EMU10K1 is pci0000:00:0c.1/gameport0, io 0xdc00, speed 1269kHz
[ 14.046013] Error: Driver 'pcspkr' is already registered, aborting...
[ 14.242060] saa7146: register extension 'dvb'.
[ 14.242233] dvb 0000:00:0a.0: PCI INT A -> Link[LNKC] -> GSI 12 (level, low) -> IRQ 12
[ 14.242554] saa7146: found saa7146 @ mem ccc5ee00 (revision 1, irq 12) (0x13c 2,0x0003).
[ 14.242721] dvb 0000:00:0a.0: firmware: requesting dvb-ttpci-01.fw
[ 15.832644] DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X)
[ 15.869295] adapter has MAC addr = 00:d0:5c:21:2d:4e
[ 16.182950] dvb-ttpci: gpioirq unknown type=0 len=0
[ 16.208095] dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010 068, app 80002622
[ 16.208169] dvb-ttpci: firmware @ card 0 supports CI link layer interface
[ 16.376135] dvb-ttpci: adac type set to 0 @ card 0
[ 16.384287] saa7146_vv: saa7146 (0): registered device video0 [v4l2]
[ 16.384432] saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
[ 16.968285] DVB: registering adapter 0 frontend 0 (ST STV0299 DVB-S)...
[ 16.968783] input: DVB on-card IR receiver as /devices/pci0000:00/0000:00:0a. 0/input/input4
[ 16.970609] dvb-ttpci: found av7110-0.
[ 16.972159] EMU10K1_Audigy 0000:00:0c.0: PCI INT A -> Link[LNKA] -> GSI 10 (l evel, low) -> IRQ 10
[ 16.987297] Control name 'Sigmatel Surround Phase Inversion Playback Switch' truncated to 'Sigmatel Surround Phase Inversion Playback '
[ 18.974625] Adding 562232k swap on /dev/hda5. Priority:-1 extents:1 across:5 62232k
[ 19.208314] EXT3 FS on hda1, internal journal
[ 20.208167] loop: module loaded
[ 20.379686] device-mapper: uevent: version 1.0.3
[ 20.385770] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-d evel@redhat.com
[ 22.461090] kjournald starting. Commit interval 5 seconds
[ 22.461558] EXT3 FS on hda6, internal journal
[ 22.461660] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.500307] kjournald starting. Commit interval 5 seconds
[ 22.500797] EXT3 FS on hdb, internal journal
[ 22.500900] EXT3-fs: mounted filesystem with ordered data mode.
[ 23.711903] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 25.799615] NET: Registered protocol family 10
[ 25.801078] lo: Disabled Privacy Extensions
[
-
Ich bin kein lirc user aber poste mal deine hardware.conf und lircd.conf
zu deinem log:
lirc schaut mal soweit ich das einschätzen kann ordentlich installiert zu sein und treiber wird geladen
[ 6.296167] usb 3-2: new low speed USB device using ohci_hcd and address 2
[ 6.528443] usb 3-2: configuration #1 chosen from 1 choice
[ 6.531703] usb 3-2: New USB device found, idVendor=0bc7, idProduct=0006
[ 6.531783] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.531846] usb 3-2: Product: RF receiver
[ 6.531900] usb 3-2: Manufacturer: X10 WTI
[ 10.994819] lirc_dev: IR Remote Control driver registered, major 61
[ 11.064253] lirc_atiusb: USB remote driver for LIRC $Revision: 1.69 $
[ 11.064371] lirc_atiusb: Paul Miller <pmiller9@users.sourceforge.net>
[ 11.100232] lirc_dev: lirc_register_plugin: sample_rate: 0
[ 11.168089] lirc_atiusb[2]: X10 WTI RF receiver on usb3:2
[ 11.184152] usbcore: registered new interface driver lirc_atiusb
Da get's dann los...
[ 11.530145] ACPI: I/O resource amd756_smbus [0x50e0-0x50ef] conflicts with ACPI region SBS_ [0x50e0-0x50e8]
[ 11.530237] ACPI: Device needs an ACPI driver
Das klingt nicht gut... ich hab abe leider keine Ahnung was es bedeutet, Sorry.
Gute Dokumentation über lirc haben sie im ubuntuusers wiki (http://wiki.ubuntuusers.de/Lirc#hardware-conf-einrichten). Nach der beschreibung ists eigentlich leitcht hinzubekommen. Ansonsten würd ich da zum vdrportal raten. Da du ja anscheinend eine vdr spezialdistro einsetzt gibts dort sicher jemand der schonmal dasselbe problem hatte.
-
Ansonsten würd ich da zum vdrportal raten.
da bin ich auch schon tätig und bis jetzt keine lösung
hier mal die configs.
hardware.conf3:
# /etc/lirc/hardware.conf
#
# Arguments which will be used when launching lircd
LIRCD_ARGS=""
#Don't start lircmd even if there seems to be a good config file
#START_LIRCMD=false
#Don't start irexec, even if a good config file seems to exist.
#START_IREXEC=false
#Try to load appropriate kernel modules
LOAD_MODULES=true
# Run "lircd --driver=help" for a list of supported drivers.
DRIVER="default"
# If DEVICE is set to /dev/lirc and udev is in use /dev/lirc0 will be
# automatically used instead
DEVICE="/dev/lirc"
MODULES="lirc_atiusb"
# Default configuration files for your hardware if any
LIRCD_CONF=""
LIRCMD_CONF=""
lircd.conf:
# Please make this file available to others
# by sending it to <lirc@bartelmus.de>
#
# this config file was automatically generated
# using lirc-0.8.3(default) on Fri Oct 30 18:53:19 2009
#
# contributed by
#
# brand: ./7552.fb.conf
# model no. of remote control:
# devices being controlled by this remote:
#
begin remote
name ./7552.fb.conf
bits 16
eps 30
aeps 100
one 0 0
zero 0 0
pre_data_bits 8
pre_data 0x14
post_data_bits 16
post_data 0x0
gap 219962
min_repeat 21
toggle_bit_mask 0xD9020000
begin codes
Power 0xD702
Guide 0x86B1
Text 0xEB16
Lauter 0x5E89
Leiser 0xDD08
Mute 0x5580
Programm+ 0xE00B
Programm- 0x618C
LiveTV 0xF11C
RecTV 0x6D98
Photo 0xDA05
Music 0xDB06
DVD_Menue 0xD904
Video 0x82AD
Rot 0x0732
Blau 0x8AB5
Gelb 0x0934
Grün 0x88B3
Pfeil_Links 0xF21D
Pfeil_rechts 0x749F
Pfeil_oben 0xEF1A
Pfeil_unten 0x77A2
OK 0xF31E
1 0x628D
2 0xE30E
3 0x648F
4 0xE510
5 0x6691
6 0xE712
7 0x6893
8 0xE914
9 0x6A95
0 0x6C97
* 0x0C37
# 0x8DB8
Back 0xF520
Info 0x84AF
World 0xF01B
rewind 0x79A4
Play 0xFA25
Forward 0x7BA6
Pause 0xFE29
SkipPrior 0x76A1
SkipNext 0xF823
Stop 0x7DA8
Record 0xFC27
end codes
end remote
-
meine x10 pollin habe ich zun laufen gebracht (es lag an der hardware.conf)...erstmal das angenehme.
das unangenehme wenn ich die menütaste oder einen der farbtasten drücke startet sich der vdr neu.an was liegt das denn?
-
eventuell falscher keycode ?
-
eventuell falscher keycode ?
welchen keycode? eine lircd.conf habe ich mit irrecord selberhergestellt und die andere vom inet. bei allen beiden dasselbe.
ich hoffe du meinst das damit.
-
ja, das meinte ich, aber wenn du es eh selbst erstellt hat sollte es schon passen. Gibt es in den logs gar nichts zu den vdr crashes zu finden?
Eventuell ist ein plugin der übeltäter. Deaktiviere alle plugins beim vdrstart und versuch dann nochmals ob sich der vdr aufhängt.
Kannst du bitte die richtige hardware.conf noch anhängen. Darüber wird sich der nächste der über den thread stolpert sicher freuen ;)
-
ich habe es jetzt hinbekomen :laugh: :laugh: :laugh:
die fb und alle funktionen funktionieren.
das problem war das plugin menuorg welches ich in meiner vdr anfangszeit installiert und dann vergessen hatte.
Hier die Lircd.conf und die Hardware.conf für die x10 von Pollin
Das Teil hat 7,95 plus versandgebühren gekostet und ist sehr zum empfehlen.
ich kann jetzt meinen vdr vom schlafzimmer aus bedienen ;D sowas hat zukunft
gruß
dippes
-
Na dann gratuliere!
Schaut ja nett aus diese FB 8)